Showing posts with label how to make a solar mobile phone charger. Show all posts
Showing posts with label how to make a solar mobile phone charger. Show all posts

Thursday, June 21, 2012

How to : DIY Solar Backpack with Solar Mobile phone charger and LED Lighting


Solar Backpack with Solar Mobile phone charger
The Finished Solar Backpack!


Introduction

Last year , i was trekking in the mountains and was surprised by the lack of electricity. Although there was an abundance of sunlight during the day, all lighting there during the evenings/night was with oil lamps which not only smoky but provided very little light. Vowing to return next year better prepared,  i made a solar backpack. It can be also used to power widgets such as the arduino, raspberry pi, etc.  Here are the features:
  • Can charge upto 6 mobile phones at one time!
  • 140 lumen high power led lighting
  • 27wh high capacity battery
  • Modular Design for expansion
DIY solar mobile phone charger
Success!

Materials Required:

Backpack:
  • 5W Solar panel for 6v battery
  • Old Bag / Bagpack
  • General Purpose PCB
  • Schottky Diode (1n5189/ SS14 etc)
  • 6v Sealed Lead Acid battery
  • 2 pin Terminal plug
Solar Mobile Phone Charger Circuit:
  •  5v 3A LDO (I used a ucc383. You can use an LDO with a lower current capacity also)
  • Heatsink for the TO-220 package LDO
  • USB Port
Light engine:
  • High Power led (Can be 1w-3w. I used a CREE XM-L as it is the most efficient led  the world) 
  • Heat Sink for LED
  • Lens/Reflector for the LED
  • LED Driver

Instructions

  • Attach the solar panel to the backpack. You can stitch it, use hot glue, epoxy or any other adhesive as you see fit. I used a synthetic rubber based adhesive called FeviBond.
  • Using a general purpose board, construct the following circuit:
Circuit Diagram for solar mobile phone charger

Circuit Diagram for solar backpack



    • The USB port can be used as a solar mobile phone charger to charge phones, tablets etc.   
    • My PCB looked like this:
    PCB for solar mobile phone charger

    PCB of Solar Backpack


    • To make the light engine, i soldered some wire to the Cree XML led and mounted it on the heat sink.
    • Although the Cree XML can be driven with 3 Amps or current giving a staggering 1000 lumens, i could not find a suitable driver. Hence, i am using a 350ma driver.
    Power led mounted on heatsink
    Led mounted on heatsink
    • Some LED drivers, for use as halogen replacements have a bridge rectifier.If you wish, you can remove the diodes as they cause a voltage drop of about one volt. I removed them as they reduce efficiency
    • Mount the led driver on the other side of the heat sink



    Led driver mounted on a heatsink
    Led Driver mounted on heatsink

    • Attach the reflector or lens to the led. 


    Reflector mounted on a led
    Reflector mounted on the led
    Enjoy your eco-freindly power source! In the picture below, it is a solar mobile phone charger!
    mobile phone being powered by solar panel
    Mobile phone being powered by 100% solar power!

    In the picture below, the Arduino Uno is being powered by the solar backpack, making it a solar powered arduino! You can also use this to power the Raspbery Pi, Teensy etc!

    solar powered arduino
    Solar Powered Arduino



    Saturday, July 2, 2011

    I got a new solar panel - Battery charging

    So recently, i bought a new solar panel. Its capacity is 5W and it is very handy for the summer months in india. It can easily charge a 6v 4.5AH SLA (Sealed Lead Acid) battery. My charging setup is as follows-

    Solar panel -> 1n4007 diode -> Battery

    The battery can store up to 27 WH and gets charged in one day easily.

    I check on the setup regularly with a multimeter.

    Lead acid batteries are every well suited to charging with a solar panel since they are not fussy about over charge/undercharge, they can store large amounts of current for a very less cost, and they can be drip charged. The battery in question costed me about $5, very cheap compared to a li-ion solution.
    They charged battery is then used to charge various mobile phones as well as for lighting during power cuts. I plan to expand this system with a 12v 7.2 AH battery and a 20 Watt solar panel. Also, i want to upgrade the diode form an 1n4001 to a shottky diode because the voltage drop is much less then normal rectifiers!
    6v 4.5AH Sealed Lead Acid Battery
    6v 4.5AH Sealed Lead Acid Battery

    5W Solar Panel
    5W Indian Manufactured Solar Panel

    Solar panel battery charging
    Solar Panel with battery for charging